Binder C 150 User Manual Page 76
- Page / 90
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
C 150 (E2) 12/2012 page 76/90
18. Troubleshooting
Fault description
Possible cause
Required measures
General
Unit without function.
No power supply.
Check connection to power sup-
ply.
Wrong voltage.
Check power supply for voltage of
115V / 208 - 240 V / 230V.
Nominal temperature exceeded
by 10 °C due to unit failure. Over
temperature protective device
(class 1) responds (chap. 9.1).
Contact BINDER service.
The miniature fuse for overcur-
rent protection has triggered
(chap. 19.2).
Check unit fuse and replace it if
appropriate. If it responds again,
contact BINDER service.
Controller defective.
Contact BINDER service.
Message “dor” is displayed.
The outer unit door is not closed
properly.
Close unit door properly.
Heating
Chamber does not heat up.
Pt 100 sensor defective.
Contact BINDER service.
Heating element defective.
Semiconductor relay defective.
Temperature inside too low.
Doors not closed.
Close door properly.
Door gaskets defective.
Replace door gaskets.
Controller defective.
Contact BINDER service.
Pt 100 sensor defective.
Controller not adjusted.
Calibrate and adjust controller.
Temperature inside too low.
Message “tol” is displayed
(temperature tolerance range
alarm)
Doors not closed.
Close door properly.
Door gaskets defective.
Replace door gaskets.
Wrong controller setting.
Check and, if appropriate, set the
operating function “AL.12” (tem-
perature alarm threshold) (chap.
7.3). Value should be ≥ 1 K.
Temperature inside too high.
Installation site too warm.
Select cooler place of installation
(chap. 3.4).
Difference between the set tem-
perature and the ambient tem-
perature too low.
Difference between the set tem-
perature and the ambient tempera-
ture at least 7°.
Too much external heat load.
Reduce heat load.
Controller defective.
Contact BINDER service.
Semiconductor relay defective.
Controller not adjusted.
Calibrate and adjust controller
Temperature inside too high.
Message “tol” is displayed (tem-
perature tolerance range alarm).
Installation site too warm.
Select cooler place of installation
(chap. 3.4).
Difference between the set tem-
perature and the ambient tem-
perature too low.
Difference between the set tem-
perature and the ambient tempera-
ture at least 7°.
Too much external heat load.
Reduce heat load.
Semiconductor relay defective.
Contact BINDER service.
Wrong controller setting.
Check and, if appropriate, set the
operating function “AL.12” (tem-
perature alarm threshold) (chap.
7.3). Value should be ≥ 1 K.
- Operating Manual 1
- EG – KONFORMITÄTSERKLÄRUNG 2
- page 3/90 3
- page 4/90 4
- Product registration 5
- Contents 6
- page 7/90 7
- page 8/90 8
- 1. Safety 9
- WARNING 10
- CAUTION 10
- page 11/90 11
- 1.4 Type plate 12
- C 150 Serial No. 00-00000 13
- 2. Unit description 17
- 2.2 Unit overview 18
- page 19/90 19
- page 28/90 28
- 5. Start up 31
- page 33/90 33
- 7.2 Operating mode HAND 34
- page 35/90 35
- page 36/90 36
- page 37/90 37
- page 38/90 38
- page 39/90 39
- page 40/90 40
- 8. Controller RP1 settings 41
- page 42/90 42
- page 43/90 43
- page 45/90 45
- page 46/90 46
- page 47/90 47
- 10. Alarm functions 48
- page 49/90 49
- page 50/90 50
- 10.6 Door open 51
- 10.7 CO 52
- tolerance range alarm (CO 52
- over/under concentration) 52
- 10.8 CO 52
- pressure too low 52
- 11. Error messages 54
- 12. Reference measurements 55
- 12.1.2 Measuring CO 56
- 13. Options 57
- 14.1 Cells and media 59
- incubator C 150 60
- 14.5 Handling the CO 61
- VORSICHT 64
- page 67/90 67
- page 70/90 70
- 16.3 Gas inlet fine filter 71
- 17. Disposal 72
- 17.2 Decommissioning 73
- 18. Troubleshooting 76
- page 77/90 77
- page 78/90 78
- 19. Technical description 79
- 19.4 C 150 technical data 80
- page 81/90 81
- page 82/90 82
- page 83/90 83
- 19.9 Dimensions C 150 84
- page 85/90 85
- page 86/90 86
- page 87/90 87
- page 88/90 88
- page 89/90 89
- page 90/90 90
Related products and manuals for Equipment Binder C 150
Equipment Binder C 150 User Manual
(89 pages)
(89 pages)
Equipment Binder C 150 User Manual
(91 pages)
(91 pages)
Equipment Binder C 150 User Manual
(93 pages)
(93 pages)
Equipment Binder CB 60 User Manual
(145 pages)
(145 pages)
Equipment Binder CB 60 User Manual
(143 pages)
(143 pages)
Equipment Binder CB 60 User Manual
(145 pages)
(145 pages)
Equipment Binder CB 60 User Manual
(145 pages)
(145 pages)
Equipment Binder CB 53 User Manual
(111 pages)
(111 pages)
Equipment Binder CB 60 User Manual
(145 pages)
(145 pages)
Equipment Binder B 28 User Manual
(39 pages)
(39 pages)
Equipment Binder B 28 User Manual
(39 pages)
(39 pages)
Equipment Binder B 28 User Manual
(39 pages)
(39 pages)
Equipment Binder B 28 User Manual
(39 pages)
(39 pages)
Equipment Binder BD 23 User Manual
(63 pages)
(63 pages)
Equipment Binder BD 23 User Manual
(63 pages)
(63 pages)
Equipment Binder BD 23 User Manual
(67 pages)
(67 pages)
Equipment Binder BD 23 User Manual
(63 pages)
(63 pages)
Equipment Binder BF 53 User Manual
(51 pages)
(51 pages)
Equipment Binder BD 23 User Manual
(67 pages)
(67 pages)
Equipment Binder BF 53 User Manual
(53 pages)
(53 pages)
© 2020, manymanuals.com. All rights reserved. | 0.686 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals